How to Select the Right Tip for Your Paint Gun

When spraying paint with a compressed air spray gun – whether gravity feed or siphon feed, conventional or High Volume Low Pressure (HVLP) – it’s important to have the gun set up properly for the job. What you are painting is important to a certain extent, but more important is what you are painting with.


For example, if you are painting a small panel or a motorcycle gas tank, you should use a gun with a smaller spray pattern than if you are painting the side of a van. You can still use the big gun for a small project, but it is going to be more wasteful and messy. Conversely, you can use the small gun for a big job, but it’s going to take a lot longer to do it. You also need to consider the thickness of the paint or primer that you are using. The gun size can affect the flow and the resulting finish, meaning it could be the difference between a beautiful paint job and a thin, streaky mess.


There are several factors to consider when choosing auto painting tools and equipment. But most important to the quality of the job you are doing is using a gun with the right size fluid tip and needle for paint, primer or whatever else you are spraying. Choosing the proper HVLP spray gun tip size will give you the right combination of speed, efficiency, results and ease of clean-up.

Different HVLP Paint Gun Tip Sizes

Most guns have the option of several different-sized spray tip openings with a matching needle for each one. Eastwood carries a selection of popular sizes for the guns we sell. As a general rule of thumb, thicker material like high-build primers use a bigger opening, while thinner liquids use a smaller tip.

Oftentimes, the paint or primer will come with recommendations as to how to spray it. Usually the instructions that come with the gun will have a handy spray gun tip size chart too. Here’s what Kevin Tetz and Eastwood recommends for the Concourse HVLP gun.

spray gun tips

For spraying clear coats on small parts and projects, we recommend a 1.2mm tip. For spraying a whole car, a 1.3mm tip is recommended. The 1.4mm tip is perfect for base coats and metallic as the droplet size allows the particles to self-orient to eliminate streaking and mottling. The 1.8mm is at the upper end of sizes for urethane primer surfacers, and the minimum size you want to use for a poly-urethane primer surfacer, which can use up to a 2.2mm.

Here are some common tip sizes and recommended usages:

5 tip

0.5-1.0mm These are very common in detail spray guns because they provide a much smaller pattern compared to a larger tip on a full size gun. They are also used for thin dyes and stains.

1.2mm, 1.3mm Good for clear coat and thinner base coats. Spraying clear with a 1.2mm will take longer because the tiny hole doesn’t flow much fluid through it but will give you a very fine finish. The 1.3mm is a great general clear coat tip and is also good for thinner base coats, waterborne and single-stage paints. Too thick of a paint won’t flow well through this size, though.

1.4mm Great all-purpose size. Works well with most base coats, and even thicker clears. This size is the closes to a universal tip as it comes. When in doubt, it’s a good place to start.

1.5mm, 1.6mm Versatile tip for base coats and single-stage paints. Thinner paints run the risk of orange peel, though, because they will not atomize correctly. These sizes are also a good choice for lacquer paints.

1.7mm, 1.8mm  – 1.7mm is the smallest size you should use for most types of primer. It is not a very common size but is currently offered on the Eastwood Concours LT Gun. Typically, 1.8mm is recommended for most primer surfacers. It’s also the smallest size if you are shooting latex paint – not that you would do that with your good HVLP gun.


2.0-2.3mm For high-build primers and other thick materials. Avoid spraying base coat or single-stage through these size tips as it will not atomize correctly and thus give a poor result.

pro set
If you still are unsure what paint spray tip sizes you will need, Eastwood makes it easy by offering our Original Concours and Concours Pro HVLP paint guns in sets that come with multiple sizes. Purchasing a set like these will allow you to spray all types of paints from the same gun, making it easier while saving you money.

This concludes our rundown of the common sizes of fluid tips for the HVLP spray gun and what they are for, with the most common in red in the above picture. If you just remember that thinner = smaller and thicker = bigger, it’s pretty intuitive. With fancy paints like pearls and metal flakes, you may have to go smaller and larger respectively for them to come out really well, but the only real way to find out is with practice – lots of practice.

One Comment

  1. Hi, good information. I bought the Devilbiss FLG-670 spray gun with three tips but it had only one needle. Does every tip size need it’s own individual needle? Just curious. I’m thinking about getting the 1.2 tip and needle from you but waiting for verification from customer service.
    Thanks, Les

Leave a Reply

Back to top button